Skip to main content Skip to search Skip to main navigation

Industry

Industrial pipes, Gray metal, Flanged joints, Pipe maintenance

Sealing sewage pipes: a quick and low-cost solution!

Sewage or drainage pipes are part of large drainage or sewage treatment plants. They are built into buildings or run underground. Although they are generally constructed to last a long time, they are subject to wear, tear and ageing due to continuous use. If there are holes in a drainage pipe or any other damages, rapid action is required. We show you how to sealing sewage pipes – quickly and at low cost!

Wear and corrosion on sewage pipes

Sewage pipes and pipelines are exposed to enormous loads every day. They mainly transport water from one place to another. But not all water is the same: sewage pipes have to cope with varying degrees of strain, ranging from wastewater to rainwater or mixed water. It is evident that it makes a big difference whether wastewater from toilets runs through the pipes or clean rainwater. The amount of dirt or chemicals in the water determines the speed at which wear and corrosion occur.

Sealing sewage pipes – an application example

The following case occurred at a wastewater clarifier: the return pipes were quite old and there were holes in the pipe wall due to corrosion and wear. The pipes were leaking and starting to drip. So a fast repair solution was needed. But how can a sewage pipe be sealed without disconnecting it from the entire system?

Preparations for repair work – what requires special attention?

After an initial assessment of the damaged sewage pipes, the right product was selected and the repair work planned. Important fact: the temperature in the sewage treatment plant was around eleven degrees. This is not a great temperature for applying repair products, which is why we heated the room in the sewage treatment plant to 15 degrees with the help of radiant heaters.

ชุดซ่อมแซมท่อ | สำหรับการซ่อมแซมฉุกเฉิน สำหรับท่อที่มีความเสียหาย
ชุดซ่อมแซมท่อ
สำหรับการซ่อมแซมฉุกเฉิน สำหรับท่อที่มีความเสียหาย
รายละเอียด

Ready to start: sealing sewage pipes step by step




In order to be able to seal the sewage pipe, we first focused on the surface pre-treatment. We sandblasted the damaged pipes, e.g. to remove old paint. We then applied our WEICON Cleaner Spray S and cleaned the pipes.

Now the actual repair work began. First of all, the holes had to be filled. To do this, we slightly heated some wire mesh, then we adjusted its shape and placed it on the damaged sewage pipe for stabilisation. To fix the wire mesh to the pipe, we attached its corners with our WEICON Repair Stick Copper. In the next step, our steel-filled epoxy resin system WEICON A was used. The epoxy resin system is perfect for removing corrosion damage and pitting or for repairing holes and cavities. In this case, WEICON A provides a real alternative to welding, as the application of the epoxy resin does not cause thermal distortion as in welding.


Let’s continue! To seal the sewage pipe, further stabilisation with our WEICON Pipe Repair-Kit is required. It is used for the emergency repair of damaged pipes and pipelines. The set includes a repair tape with glass-fibre reinforced plastic which is impregnated with a special resin. If you immerse it in clean water and then wrap it around the damaged area, the special resin hardens after around 30 minutes. Once fully cured, the repair tape can be painted over or coated.

Finally, we sealed the sewage pipes with WEICON Ceramic BL. The mineral-filled epoxy resin system protects against corrosion and provides sewage pipes with an appropriate finish.

Save time, money and resources

The entire repair on site took just five hours. And it took around 24 hours for the products to cure fully. The pipes were then ready for use again. To mention it once again: the repair was carried out without dismantling the pipes, which saved an enormous amount of time. If the customer had had to install new pipes or dismantle the old ones for repair, the sewage treatment plant would have been out of action for several days. In addition, a new pipe would have cost three times as much. Another advantage? Repairing the sewage pipes is more sustainable: instead of installing new sewage pipes, material resources were saved by repairing the old ones.

pipes, valves, industrial, piping, basement
grinding, mesh, pad, gloves, bolts
industrial, machinery, metallic, work gloves, man in workshop
blue pipe, gloved hands, worksite, metal elbow, welding/pipework
Comment area
Write a comment
Your comment will be released after review.
More article
  • Railway wheelset, Steel train wheels, Industrial machinery, FAG bearings, Rusty metal
    Installation of an emergency safety catch on a suspension railway
    For more than a century, suspension railways have been among the most fascinating transport systems in the world. The Wuppertal suspension monorail – perhaps the most iconic of its kind – has been in operation since 1901. And continues to represent engineering innovation and future-oriented urban mobility. Suspension railways differ from traditional trains by travelling suspended from an elevated track. Usually through cities or densely populated urban areas. This unique design offers numerous advantages: it takes up no road space, runs quietly and efficiently, and avoids the delays of street-level traffic. Today, suspension railways are used worldwide. In various forms, as part of public transport systems, airport shuttles or within industrial facilities. Suspension railway systems not only require the highest precision in construction, but also in maintenance and servicing. Repairs often need to be carried out quickly, safely and with lasting precision during operation. This is illustrated in the following example: Installation of an emergency safety catch on a suspension railway.
    Read the article now
  • conveyor belt, rubber belt, industrial conveyor, black belt, belt surface
    Conveyor Belt Repair: Here's How to Do It Quickly and Cost-Effectively!

    Conveyor belts tirelessly transport materials from point A to point B. In the process, raw materials such as stones, sand, coal, and the like are jostled and rattled along the conveyor belt. Even the sturdiest conveyor belt cannot withstand this constant strain without showing signs of wear. The inevitable impacts, oscillations, and vibrations literally put the rubber of the conveyor belts to the test.

    After some time in operation, wear and tear becomes apparent in the form of holes or tears in the conveyor belt. Now it’s time for a quick conveyor belt repair!

    Read the article now